I installed “DietPi_NanoPiR6C-ARMv8-Bookworm.img” ( https://dietpi.com/downloads/images/DietPi_NanoPiR6C-ARMv8-Bookworm.img.xz ) on the internal EMMC of an NanoPi R6C (e) but if i bootup after installation the NanoPi does not boot up, just the SYS Led is solid red.
Installing the image on the internal emmc was done using the eflasher tool integrated in the NanoPi Friendly Elec Web tool. ( see NanoPi R6C - FriendlyELEC WiKi >> 4.5.3.2 Option 2: Install OS on Web Page )
Here in the Forum a already found similar topics but none with a real solution for my problem.
EDIT:
Tried the same Image booting directly from the SD card but this doesn’t work either
Only solid red light.
Here is the output of the "Serial Debug "
<\0><\0>DDR V1.11 f1474cf52f cym 23/05/09-11:02:36<\r><\n>
LPDDR4X, 2112MHz<\r><\n>
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB<\r><\n>
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB<\r><\n>
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB<\r><\n>
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB<\r><\n>
Manufacturer ID:0x1<\r><\n>
CH0 RX Vref:27.1%, TX Vref:21.8%,20.8%<\r><\n>
CH1 RX Vref:25.8%, TX Vref:19.8%,20.8%<\r><\n>
CH2 RX Vref:26.7%, TX Vref:21.8%,20.8%<\r><\n>
CH3 RX Vref:25.0%, TX Vref:21.8%,21.8%<\r><\n>
change to F1: 528MHz<\r><\n>
change to F2: 1068MHz<\r><\n>
change to F3: 1560MHz<\r><\n>
change to F0: 2112MHz<\r><\n>
out<\r><\n>
U-Boot SPL board init<\r><\n>
U-Boot SPL 2017.09-armbian (May 21 2024 - 16:21:13)<\r><\n>
unknown raw ID 0 0 0<\r><\n>
unrecognized JEDEC id bytes: 00, 00, 00<\r><\n>
Trying to boot from MMC2<\r><\n>
part_get_info_efi: *** ERROR: Invalid GPT ***<\r><\n>
part_get_info_efi: *** Using Backup GPT ***<\r><\n>
spl: partition error<\r><\n>
Trying fit image at 0x4000 sector<\r><\n>
Not fit magic<\r><\n>
Trying fit image at 0x5000 sector<\r><\n>
Not fit magic<\r><\n>
Trying to boot from MMC1<\r><\n>
spl: partition error<\r><\n>
Trying fit image at 0x4000 sector<\r><\n>
## Verified-boot: 0<\r><\n>
## Checking atf-1 0x00040000 ... sha256(7efcd01a0f...) + OK<\r><\n>
## Checking uboot 0x00200000 ... sha256(2f31ed4655...) + OK<\r><\n>
## Checking fdt 0x0031ec90 ... sha256(c5d44f02b4...) + OK<\r><\n>
## Checking atf-2 0x000f0000 ... sha256(da90adf3a4...) + OK<\r><\n>
## Checking atf-3 0xff100000 ... sha256(1163474a5b...) + OK<\r><\n>
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)<\r><\n>
Total: 165.618/316.94 ms<\r><\n>
<\r><\n>
INFO: Preloader serial: 2<\r><\n>
NOTICE: BL31: v2.3():v2.3-589-g3389cfdda:derrick.huang<\r><\n>
NOTICE: BL31: Built : 10:14:29, May 9 2023<\r><\n>
INFO: spec: 0x13<\r><\n>
INFO: ext 32k is valid<\r><\n>
INFO: ddr: stride-en 4CH<\r><\n>
INFO: GICv3 without legacy support detected.<\r><\n>
INFO: ARM GICv3 driver initialized in EL3<\r><\n>
INFO: valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0<\r><\n>
INFO: system boots from cpu-hwid-0<\r><\n>
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001<\r><\n>
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz<\r><\n>
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz<\r><\n>
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz<\r><\n>
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz<\r><\n>
INFO: BL31: Initialising Exception Handling Framework<\r><\n>
INFO: BL31: Initializing runtime services<\r><\n>
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK<\r><\n>
ERROR: Error initializing runtime service opteed_fast<\r><\n>
INFO: BL31: Preparing for EL3 exit to normal world<\r><\n>
INFO: Entry point address = 0x200000<\r><\n>
INFO: SPSR = 0x3c9<\r><\n>
<\r><\n>
<\r><\n>
U-Boot 2017.09-armbian (May 21 2024 - 16:21:13 +0000)<\r><\n>
<\r><\n>
Model: NanoPi R6S<\r><\n>
MPIDR: 0x81000000<\r><\n>
PreSerial: 2, raw, 0xfeb50000<\r><\n>
DRAM: 8 GiB<\r><\n>
Sysmem: init<\r><\n>
Relocation Offset: eda3f000<\r><\n>
Relocation fdt: eb9f9960 - eb9fecd0<\r><\n>
CR: M/C/I<\r><\n>
Using default environment<\r><\n>
<\r><\n>
optee check api revision fail: -1.0<\r><\n>
optee api revision is too low<\r><\n>
### ERROR ### Please RESET the board ###<\r><\n>
Please note that in the debug output the model is shown as “Model: NanoPi R6S” where it should be “NanoPi R6C”.
EDIT2:
Just tried a official image from Friendlyelec (rk3588-sd-friendlywrt-23.05-20240511.img) and this works right out of the box (from SD card)
Is there an option to download old images ?
I already installed my system in 2023 without such problems and need a quick solution now to get back to operation on this system.
EDIT3:
Now found an old NanoPiR6S image (“DietPi_NanoPiR6S-ARMv8-Bullseye.img”) with date from 13.03.2023) and this works as expected. (note that this working image is for R6S and not for my R6C Hardware)
Any help is appreciated to get a new image version working.