(resolved) calling CRDA many times and failing on boot.

Having issues with your DietPi installation, or, found a bug? Post it here.
Gord_W
Posts: 134
Joined: Sat Oct 24, 2015 6:30 pm

(resolved) calling CRDA many times and failing on boot.

Post by Gord_W »

Hi,

On booting up dietpi on a rpi B it takes a while before the wireless comes up and I can ssh into it. I'm running it headless with dietpi v92.

dmesg shows the info below. Lots of time is spent calling CRDA. Can this be set so this doesn't happen?

I'm not sure why CRDA can't be found. The rpi has an internet connection.

What can I do to speed up the time from power on to being able to ssh into the rpi.?

Thanks,
Gordon Williams


[ 2.060620] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem
[ 2.074497] EXT4-fs (mmcblk0p2): write access will be enabled during recovery
[ 2.143721] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.158443] Indeed it is in host mode hprt0 = 00001101
[ 2.374540] usb 1-1: New USB device found, idVendor=0424, idProduct=9512
[ 2.388859] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.404689] hub 1-1:1.0: USB hub found
[ 2.416735] hub 1-1:1.0: 3 ports detected
[ 2.703723] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 2.814090] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 2.827160] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.843808] smsc95xx v1.0.4
[ 2.908733] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-20980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:a5:0d:22
[ 3.003689] usb 1-1.3: new high-speed USB device number 4 using dwc_otg
[ 3.135215] usb 1-1.3: New USB device found, idVendor=0cf3, idProduct=9271
[ 3.149039] usb 1-1.3: New USB device strings: Mfr=16, Product=32, SerialNumber=48
[ 3.163353] usb 1-1.3: Product: USB2.0 WLAN
[ 3.173866] usb 1-1.3: Manufacturer: ATHEROS
[ 3.184828] usb 1-1.3: SerialNumber: 12345
[ 7.899081] EXT4-fs (mmcblk0p2): recovery complete
[ 8.255334] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 8.270064] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 8.285529] devtmpfs: mounted
[ 8.296047] Freeing unused kernel memory: 348K (c07c3000 - c081a000)
[ 10.082457] udevd[159]: starting version 175
[ 11.454022] gpiomem-bcm2835 20200000.gpiomem: Initialised: Registers at 0x20200000
[ 12.466613] cfg80211: Calling CRDA to update world regulatory domain
[ 12.863542] usb 1-1.3: ath9k_htc: Firmware htc_9271.fw requested
[ 12.954152] usbcore: registered new interface driver ath9k_htc
[ 13.166174] usb 1-1.3: ath9k_htc: Transferred FW: htc_9271.fw, size: 51272
[ 13.249978] random: nonblocking pool is initialized
[ 13.412086] ath9k_htc 1-1.3:1.0: ath9k_htc: HTC initialized with 33 credits
[ 15.654128] cfg80211: Calling CRDA to update world regulatory domain
[ 15.880552] ath9k_htc 1-1.3:1.0: ath9k_htc: FW Version: 1.3
[ 15.913913] ath9k_htc 1-1.3:1.0: FW RMW support: Off
[ 15.933892] ath: EEPROM regdomain: 0x809c
[ 15.933923] ath: EEPROM indicates we should expect a country code
[ 15.933940] ath: doing EEPROM country->regdmn map search
[ 15.933961] ath: country maps to regdmn code: 0x52
[ 15.934020] ath: Country alpha2 being used: CN
[ 15.934033] ath: Regpair used: 0x52
[ 16.065344] ieee80211 phy0: Atheros AR9271 Rev:1
[ 16.104087] cfg80211: Calling CRDA to update world regulatory domain
[ 18.183520] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 18.843962] cfg80211: Calling CRDA to update world regulatory domain
[ 19.185282] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 22.044036] cfg80211: Calling CRDA to update world regulatory domain
[ 25.233852] cfg80211: Calling CRDA to update world regulatory domain
[ 28.423901] cfg80211: Calling CRDA to update world regulatory domain
[ 31.614044] cfg80211: Calling CRDA to update world regulatory domain
[ 34.803859] cfg80211: Calling CRDA to update world regulatory domain
[ 36.470964] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 37.997142] cfg80211: Calling CRDA to update world regulatory domain
[ 39.894454] wlan0: authenticate with 64:66:b3:f4:35:f8
[ 40.895086] wlan0: send auth to 64:66:b3:f4:35:f8 (try 1/3)
[ 40.904435] wlan0: authenticated
[ 40.906801] ath9k_htc 1-1.3:1.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 41.154017] cfg80211: Calling CRDA to update world regulatory domain
[ 44.313780] cfg80211: Calling CRDA to update world regulatory domain
[ 47.473935] cfg80211: Calling CRDA to update world regulatory domain
[ 50.633803] cfg80211: Exceeded CRDA call max attempts. Not calling CRDA
[ 86.887378] wlan0: associate with 64:66:b3:f4:35:f8 (try 1/3)
[ 95.012187] wlan0: associate with 64:66:b3:f4:35:f8 (try 2/3)
[ 95.557869] Adding 102396k swap on /var/swap. Priority:-1 extents:1 across:102396k SSFS
[ 103.129204] wlan0: associate with 64:66:b3:f4:35:f8 (try 3/3)
[ 111.250545] wlan0: association with 64:66:b3:f4:35:f8 timed out
[ 113.812027] wlan0: authenticate with 64:66:b3:f4:35:f8
[ 114.813087] wlan0: send auth to 64:66:b3:f4:35:f8 (try 1/3)
[ 114.824596] wlan0: authenticated
[ 114.833994] wlan0: associate with 64:66:b3:f4:35:f8 (try 1/3)
[ 114.839964] wlan0: RX AssocResp from 64:66:b3:f4:35:f8 (capab=0x411 status=0 aid=3)
[ 114.864205] wlan0: associated
[ 114.864716] cfg80211: Calling CRDA to update world regulatory domain
[ 118.023912] cfg80211: Calling CRDA to update world regulatory domain
[ 121.183951] cfg80211: Calling CRDA to update world regulatory domain
[ 124.343939] cfg80211: Calling CRDA to update world regulatory domain
[ 127.503983] cfg80211: Calling CRDA to update world regulatory domain
[ 130.663991] cfg80211: Calling CRDA to update world regulatory domain
[ 133.823980] cfg80211: Calling CRDA to update world regulatory domain
[ 136.984015] cfg80211: Calling CRDA to update world regulatory domain
[ 140.144058] cfg80211: Calling CRDA to update world regulatory domain
[ 143.304102] cfg80211: Calling CRDA to update world regulatory domain
[ 146.464059] cfg80211: Calling CRDA to update world regulatory domain
[ 149.624067] cfg80211: Exceeded CRDA call max attempts. Not calling CRDA
root@dietpi:~#
User avatar
Fourdee
Site Admin
Posts: 2788
Joined: Tue Feb 06, 2007 1:36 pm

Re: calling CRDA many times and failing on boot.

Post by Fourdee »

Hi Gordon,

Done some research, appears to be an issue with Raspbian Jessie.

Going from this post, could you please try the following:

Code: Select all

apt-get install crda -y
reboot
Let me know if the error is gone, and, another copy of your dmesg please so we can check boot times. Thanks.
If you find our project or support useful, then we’d really appreciate it if you’d consider contributing to the project however you can.
Donating is the easiest – you can use PayPal or become a DietPi patron.
Gord_W
Posts: 134
Joined: Sat Oct 24, 2015 6:30 pm

Re: calling CRDA many times and failing on boot.

Post by Gord_W »

Hi,
That looks quite different now.

Not sure that it is totally correct though. If I go

root@dietpi:~# crda
COUNTRY environment variable not set.

If I run:

root@dietpi:~# iw reg get
country US:
(2402 - 2472 @ 40), (N/A, 30)
(5170 - 5250 @ 80), (N/A, 17)
(5250 - 5330 @ 80), (N/A, 23), DFS
(5735 - 5835 @ 80), (N/A, 30)
(57240 - 63720 @ 2160), (N/A, 40)

dmesg is below.

If I read it correctly it goes from a world domain to China domain to US domain
[ 8.968853] cfg80211: World regulatory domain updated:
Then
[ 12.460889] cfg80211: Regulatory domain changed to country: CN
then
[ 41.207151] cfg80211: Regulatory domain changed to country: US

Regards,
Gordon Williams



[ 1.985609] mmcblk0: mmc0:0007 SD04G 3.70 GiB
[ 1.996407] vc_vchi_sm_init: failed to open VCHI service (-1)
[ 2.002140] [vc_sm_connected_init]: failed to initialize shared memory service
[ 2.031225] [vc_sm_connected_init]: end - returning -1
[ 2.042818] mmcblk0: p1 p2
[ 2.079701] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 2.094727] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 2.110036] devtmpfs: mounted
[ 2.120663] Freeing unused kernel memory: 352K (c07c2000 - c081a000)
[ 2.144995] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.159167] Indeed it is in host mode hprt0 = 00001101
[ 2.375603] usb 1-1: New USB device found, idVendor=0424, idProduct=9512
[ 2.390052] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.405882] hub 1-1:1.0: USB hub found
[ 2.418099] hub 1-1:1.0: 3 ports detected
[ 2.705061] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 2.825656] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 2.855105] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.881315] smsc95xx v1.0.4
[ 2.964410] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-20980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:a5:0d:22
[ 3.095052] usb 1-1.3: new high-speed USB device number 4 using dwc_otg
[ 4.057517] udevd[159]: starting version 175
[ 5.442322] gpiomem-bcm2835 20200000.gpiomem: Initialised: Registers at 0x20200000
[ 8.236207] usb 1-1.3: New USB device found, idVendor=0cf3, idProduct=9271
[ 8.249942] usb 1-1.3: New USB device strings: Mfr=16, Product=32, SerialNumber=48
[ 8.264498] usb 1-1.3: Product: USB2.0 WLAN
[ 8.275567] usb 1-1.3: Manufacturer: ATHEROS
[ 8.286505] usb 1-1.3: SerialNumber: 12345
[ 8.561842] cfg80211: Calling CRDA to update world regulatory domain
[ 8.851876] usb 1-1.3: ath9k_htc: Firmware htc_9271.fw requested
[ 8.869734] usbcore: registered new interface driver ath9k_htc
[ 8.968853] cfg80211: World regulatory domain updated:
[ 8.981421] cfg80211: DFS Master region: unset
[ 8.986074] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.009673] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.024703] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.039822] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.055870] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 9.072640] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 9.089118] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 9.104336] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.119217] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 9.231936] usb 1-1.3: ath9k_htc: Transferred FW: htc_9271.fw, size: 51272
[ 9.439956] random: nonblocking pool is initialized
[ 9.477226] ath9k_htc 1-1.3:1.0: ath9k_htc: HTC initialized with 33 credits
[ 11.915647] ath9k_htc 1-1.3:1.0: ath9k_htc: FW Version: 1.3
[ 11.942270] ath9k_htc 1-1.3:1.0: FW RMW support: Off
[ 11.985238] ath: EEPROM regdomain: 0x809c
[ 11.985271] ath: EEPROM indicates we should expect a country code
[ 11.985291] ath: doing EEPROM country->regdmn map search
[ 11.985309] ath: country maps to regdmn code: 0x52
[ 11.985365] ath: Country alpha2 being used: CN
[ 11.985379] ath: Regpair used: 0x52
[ 12.127562] ieee80211 phy0: Atheros AR9271 Rev:1
[ 12.155072] cfg80211: Calling CRDA for country: CN
[ 12.460889] cfg80211: Regulatory domain changed to country: CN
[ 12.527467] cfg80211: DFS Master region: unset
[ 12.534125] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.603208] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.680331] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (N/A)
[ 12.715371] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 12.756263] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 12.826903] cfg80211: (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
[ 12.905251] cfg80211: (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4400 mBm), (N/A)
[ 12.957910] cfg80211: (63720000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 2800 mBm), (N/A)
[ 14.504028] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 15.500256] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 32.412442] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 36.165805] wlan0: authenticate with 64:66:b3:f4:35:f8
[ 37.175245] wlan0: send auth to 64:66:b3:f4:35:f8 (try 1/3)
[ 37.179336] wlan0: authenticated
[ 37.185224] ath9k_htc 1-1.3:1.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 37.195130] wlan0: associate with 64:66:b3:f4:35:f8 (try 1/3)
[ 37.198820] wlan0: RX AssocResp from 64:66:b3:f4:35:f8 (capab=0x411 status=12 aid=3)
[ 37.198908] wlan0: 64:66:b3:f4:35:f8 denied association (code=12)
[ 40.081844] wlan0: authenticate with 64:66:b3:f4:35:f8
[ 41.086752] wlan0: send auth to 64:66:b3:f4:35:f8 (try 1/3)
[ 41.089110] wlan0: authenticated
[ 41.095088] wlan0: associate with 64:66:b3:f4:35:f8 (try 1/3)
[ 41.101203] wlan0: RX AssocResp from 64:66:b3:f4:35:f8 (capab=0x411 status=0 aid=3)
[ 41.126261] wlan0: associated
[ 41.129588] cfg80211: Calling CRDA for country: US
[ 41.207151] cfg80211: Regulatory domain changed to country: US
[ 41.207234] cfg80211: DFS Master region: unset
[ 41.207250] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 41.207278] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 41.207402] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
[ 41.207724] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 41.207747] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 41.207765] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 53.622344] Adding 102396k swap on /var/swap. Priority:-1 extents:1 across:102396k SSFS
root@dietpi:~#
Gord_W
Posts: 134
Joined: Sat Oct 24, 2015 6:30 pm

Re: calling CRDA many times and failing on boot.

Post by Gord_W »

Hi,

A bit of searching I thought that I found something useful, but no

http://askubuntu.com/questions/147066/h ... -in-ubuntu

sudo apt-get install crda
sudo vi /etc/default/crda

then change the line REGDOMAIN= to your country code, eg.

REGDOMAIN=CA

I modified the file (country was blank before) as above and rebooted
dmesg was about the same - actually took longer to associate with the router but I don't think that is associated with this problem.

Interestingly CRDA still is not set even though I added the country code :(
root@dietpi:~# crda
COUNTRY environment variable not set.

Could this be set somewhere else?

Gordon Williams
User avatar
Fourdee
Site Admin
Posts: 2788
Joined: Tue Feb 06, 2007 1:36 pm

Re: calling CRDA many times and failing on boot.

Post by Fourdee »

Gord_W wrote:Hi,

A bit of searching I thought that I found something useful, but no

http://askubuntu.com/questions/147066/h ... -in-ubuntu

sudo apt-get install crda
sudo vi /etc/default/crda

then change the line REGDOMAIN= to your country code, eg.

REGDOMAIN=CA

I modified the file (country was blank before) as above and rebooted
dmesg was about the same - actually took longer to associate with the router but I don't think that is associated with this problem.

Interestingly CRDA still is not set even though I added the country code :(
root@dietpi:~# crda
COUNTRY environment variable not set.

Could this be set somewhere else?

Gordon Williams
Hi Gordon,

Thanks for the update.
When i've finished working on v99, i'll take a look and run some tests. Will let you know the results.
If you find our project or support useful, then we’d really appreciate it if you’d consider contributing to the project however you can.
Donating is the easiest – you can use PayPal or become a DietPi patron.
User avatar
Fourdee
Site Admin
Posts: 2788
Joined: Tue Feb 06, 2007 1:36 pm

Re: calling CRDA many times and failing on boot.

Post by Fourdee »

I've created a Git Ticket for this bug. Will try and run some tests soon.
If you find our project or support useful, then we’d really appreciate it if you’d consider contributing to the project however you can.
Donating is the easiest – you can use PayPal or become a DietPi patron.
Gord_W
Posts: 134
Joined: Sat Oct 24, 2015 6:30 pm

Re: calling CRDA many times and failing on boot.

Post by Gord_W »

OK, I will keep on checking back.
Gordon
User avatar
Fourdee
Site Admin
Posts: 2788
Joined: Tue Feb 06, 2007 1:36 pm

Re: calling CRDA many times and failing on boot.

Post by Fourdee »

Hi Gordon,

This will be resolved in the v100 update. You can also manually patch this issue on your system by running the following:

Code: Select all

/DietPi/dietpi/dietpi-apt-get_update 1
apt-get install iw crda --no-install-recommends -y
If you find our project or support useful, then we’d really appreciate it if you’d consider contributing to the project however you can.
Donating is the easiest – you can use PayPal or become a DietPi patron.
Gord_W
Posts: 134
Joined: Sat Oct 24, 2015 6:30 pm

Re: (resolved) calling CRDA many times and failing on boot.

Post by Gord_W »

Thanks, I will give it a try.
Gordon Williams
Gord_W
Posts: 134
Joined: Sat Oct 24, 2015 6:30 pm

Re: (resolved) calling CRDA many times and failing on boot.

Post by Gord_W »

Hi,

I have updated to V100.

It looks like it is still going World,CN,US.

I have in /etc/default/crda
REGDOMAIN=CA

So it is using US rather than CA. :roll:

Is it possible to turn off "calling CRDA" and just have the correct domain set on rPi?

When the rPi is going to be used in my project in the field, it is going to be using wifi but there isn't going to be an internet connection so calling CRDA is useless anyway.

Thanks,
Gordon

[ 2.108182] devtmpfs: mounted
[ 2.118790] Freeing unused kernel memory: 352K (c07c2000 - c081a000)
[ 2.144974] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 2.158383] Indeed it is in host mode hprt0 = 00001101
[ 2.375560] usb 1-1: New USB device found, idVendor=0424, idProduct=9512
[ 2.389715] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.405419] hub 1-1:1.0: USB hub found
[ 2.417773] hub 1-1:1.0: 3 ports detected
[ 2.705047] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 2.835785] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[ 2.861233] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.883755] smsc95xx v1.0.4
[ 2.963923] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-20980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:a5:0d:22
[ 3.095081] usb 1-1.3: new high-speed USB device number 4 using dwc_otg
[ 4.053886] udevd[159]: starting version 175
[ 5.436926] gpiomem-bcm2835 20200000.gpiomem: Initialised: Registers at 0x20200000
[ 8.236145] usb 1-1.3: New USB device found, idVendor=0cf3, idProduct=9271
[ 8.250097] usb 1-1.3: New USB device strings: Mfr=16, Product=32, SerialNumber=48
[ 8.264403] usb 1-1.3: Product: USB2.0 WLAN
[ 8.275216] usb 1-1.3: Manufacturer: ATHEROS
[ 8.286326] usb 1-1.3: SerialNumber: 12345
[ 8.545785] cfg80211: Calling CRDA to update world regulatory domain
[ 8.833075] usb 1-1.3: ath9k_htc: Firmware htc_9271.fw requested
[ 8.850617] usbcore: registered new interface driver ath9k_htc
[ 8.950334] cfg80211: World regulatory domain updated:
[ 8.962782] cfg80211: DFS Master region: unset
[ 8.967416] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 8.991099] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.006253] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.021610] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.037960] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 9.055134] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 9.071894] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 9.087413] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.102446] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 9.215288] usb 1-1.3: ath9k_htc: Transferred FW: htc_9271.fw, size: 51272
[ 9.418869] random: nonblocking pool is initialized
[ 9.460727] ath9k_htc 1-1.3:1.0: ath9k_htc: HTC initialized with 33 credits
[ 11.915438] ath9k_htc 1-1.3:1.0: ath9k_htc: FW Version: 1.3
[ 11.954711] ath9k_htc 1-1.3:1.0: FW RMW support: Off
[ 11.995310] ath: EEPROM regdomain: 0x809c
[ 11.995347] ath: EEPROM indicates we should expect a country code
[ 11.995405] ath: doing EEPROM country->regdmn map search
[ 11.995423] ath: country maps to regdmn code: 0x52
[ 11.995437] ath: Country alpha2 being used: CN
[ 11.995450] ath: Regpair used: 0x52
[ 12.146831] ieee80211 phy0: Atheros AR9271 Rev:1
[ 12.185510] cfg80211: Calling CRDA for country: CN
[ 12.319748] cfg80211: Calling CRDA for country: CN
[ 12.537913] cfg80211: Current regulatory domain intersected:
[ 12.572259] cfg80211: DFS Master region: unset
[ 12.597942] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.699800] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.774320] cfg80211: (2457000 KHz - 2482000 KHz @ 25000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.835203] cfg80211: (2474000 KHz - 2482000 KHz @ 8000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.927315] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 13.169588] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 13.245129] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 13.294252] cfg80211: (57240000 KHz - 59400000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 13.362510] cfg80211: (59400000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 14.634331] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 15.590589] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 32.532014] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 36.286007] wlan0: authenticate with 64:66:b3:f4:35:f8
[ 37.302787] wlan0: send auth to 64:66:b3:f4:35:f8 (try 1/3)
[ 37.307391] wlan0: authenticated
[ 37.312654] ath9k_htc 1-1.3:1.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 37.315165] wlan0: associate with 64:66:b3:f4:35:f8 (try 1/3)
[ 37.318871] wlan0: RX AssocResp from 64:66:b3:f4:35:f8 (capab=0x411 status=12 aid=2)
[ 37.318925] wlan0: 64:66:b3:f4:35:f8 denied association (code=12)
[ 37.683957] wlan0: authenticate with 64:66:b3:f4:35:f8
[ 38.345043] wlan0: send auth to 64:66:b3:f4:35:f8 (try 1/3)
[ 38.349907] wlan0: authenticated
[ 38.365137] wlan0: associate with 64:66:b3:f4:35:f8 (try 1/3)
[ 38.369650] wlan0: RX AssocResp from 64:66:b3:f4:35:f8 (capab=0x411 status=0 aid=2)
[ 38.393894] wlan0: associated
[ 38.394687] cfg80211: Calling CRDA for country: US
[ 38.527527] cfg80211: Regulatory domain changed to country: US
[ 38.527573] cfg80211: DFS Master region: unset
[ 38.527632] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 38.527662] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 38.527688] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A)
[ 38.527706] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s)
[ 38.527767] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 38.527789] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 50.426847] Adding 102396k swap on /var/swap. Priority:-1 extents:1 across:102396k SSFS
root@dietpi:~#
Post Reply