Mar 05 20:17:14 DietPi snapclient[421]: Sampleformat: 44100:16:2, stream: 44100:16:2
Mar 05 20:17:14 DietPi snapclient[421]: Using default buffer_time: 80 ms, default fragments: 4
Mar 05 20:17:14 DietPi snapclient[421]: Exception: Can't open default, error: No such file or directory, code: -2
Mar 05 20:17:14 DietPi snapclient[421]: Exception: Can't open default, error: No such file or directory
Mar 05 20:17:14 DietPi snapclient[421]: Snapclient terminated.
Mar 05 20:17:14 DietPi systemd[1]: snapclient.service: Main process exited, code =exited, status=1/FAILURE
Mar 05 20:17:14 DietPi systemd[1]: snapclient.service: Failed with result 'exit-code'.
```
Could be related to the DAC ? " Player name: alsa, device: default " and " PCM device “default” not found "
---
### Author:  [@Art-Ev](https://dietpi.com/forum/u/Art-Ev)
#### Post date: [6 March 2024 20:48 UTC](https://dietpi.com/forum/t/pi-zero-2w-service-fail-after-update-snapcast-client/19532/4 "2024-03-06T20:48:39Z")
```auto
aplay -l
```
Is returning
```auto
aplay: device_list:274: no soundcards found...
```
Could it be a material failure ?
Any change in dietpi audio management or drivers ?
---
### Author:  [@Joulinar](https://dietpi.com/forum/u/Joulinar)
#### Post date: [7 March 2024 05:38 UTC](https://dietpi.com/forum/t/pi-zero-2w-service-fail-after-update-snapcast-client/19532/5 "2024-03-07T05:38:08Z")
@MichaIng can you have a look
---
### Author:  [@Art-Ev](https://dietpi.com/forum/u/Art-Ev)
#### Post date: [7 March 2024 18:33 UTC](https://dietpi.com/forum/t/pi-zero-2w-service-fail-after-update-snapcast-client/19532/6 "2024-03-07T18:33:39Z")
Found something : when setting sound card on onboard hdmi or 3.5mm, `aplay -l` also returns `no soundcards found...` so it’s not the DAC (also DAC is working on my pi3 running an old installation).
Could be the same issue that [No soundcards found](https://dietpi.com/forum/t/no-soundcards-found/18773)
---
### Author:  [@MichaIng](https://dietpi.com/forum/u/MichaIng)
#### Post date: [8 March 2024 16:31 UTC](https://dietpi.com/forum/t/pi-zero-2w-service-fail-after-update-snapcast-client/19532/7 "2024-03-08T16:31:10Z")
Can you show your `config.txt`, so we see whether onboard audio has been enabled as intended:
```sh
cat /boot/config.txt
```
Why do you not use the 64-bit/ARMv8 image on RPi Zero 2W?
---
### Author:  [@Art-Ev](https://dietpi.com/forum/u/Art-Ev)
#### Post date: [10 March 2024 18:18 UTC](https://dietpi.com/forum/t/pi-zero-2w-service-fail-after-update-snapcast-client/19532/8 "2024-03-10T18:18:42Z")
Had in mind that snapcast was only available for 32bit versions, but maybe that was a while ago…
Installation redone in 64bits, soundscards still unavailables.
Config.txt :
```auto
# Docs: https://www.raspberrypi.com/documentation/computers/config_txt.html
# Overlays: https://github.com/raspberrypi/firmware/blob/54453cc6f8b2e84d3bed47a9b16ff6cae01c1f9f/boot/overlays/README
#-------Display---------
# Max allocated framebuffers: Set to "0" in headless mode to reduce memory usage
# - Defaults to "2" on RPi4 and "1" on earlier RPi models
#max_framebuffers=0
# If you get no picture, set the following to "1" to apply most compatible HDMI settings.
#hdmi_safe=1
# Uncomment to adjust the HDMI signal strength if you have interferences, blanking, or no display.
# - Ranges from "0" to "11", use values above "7" only if required, e.g. with very long HDMI cable.
# - Default on first RPi1 A/B is "2", else "5", on RPi4 this setting is ignored.
#config_hdmi_boost=5
# Uncomment if HDMI display is not detected and composite is being outputted.
#hdmi_force_hotplug=1
# Uncomment to disable HDMI even if plugged, e.g. to force composite output.
#hdmi_ignore_hotplug=1
# Uncomment to force a console size. By default it will be display's size minus overscan.
#framebuffer_width=1280
#framebuffer_height=720
# Uncomment to enable SDTV/composite output on RPi4. This has no effect on previous RPi models.
#enable_tvout=1
# SDTV mode
#sdtv_mode=0
# Uncomment to force a specific HDMI mode (this will force VGA).
#hdmi_group=1
#hdmi_mode=1
# Uncomment to force an HDMI mode rather than DVI. This enables HDMI audio in DMT modes.
#hdmi_drive=2
# Set "hdmi_blanking=1" to allow the display going into standby after 10 minutes without input.
# With default value "0", the display shows a blank screen instead, but will not go into standby.
# NB: Some legacy OpenMAX applications (OMXPlayer) cannot wake screens from real standby.
hdmi_blanking=1
# Set to "1" if your display has a black border of unused pixels visible.
disable_overscan=1
# Uncomment the following to adjust overscan.
# Use positive numbers if console goes off screen, and negative if there is too much border.
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# Rotation
#display_hdmi_rotate=0
#lcd_rotate=0
#-------RPi camera module-------
#start_x=1
#disable_camera_led=1
#-------GPU memory splits-------
gpu_mem_256=16
gpu_mem_512=16
gpu_mem_1024=16
#-------Boot splash screen------
disable_splash=1
#-------Onboard sound-----------
dtparam=audio=off
#-------I2C-------------
#dtparam=i2c_arm=off
#dtparam=i2c_arm_baudrate=100000
#-------SPI-------------
#dtparam=spi=off
#-------Serial/UART-----
# NB: "enable_uart=1" will enforce "core_freq=250" on RPi models with onboard WiFi.
enable_uart=0
#-------SD card HPD-----
# Comment to enable SD card hot-plug detection, while booting via USB or network.
# NB: This causes constant CPU load and kernel errors when no SD card is inserted.
dtparam=sd_poll_once
#-------Overclock-------
temp_limit=65
initial_turbo=20
#over_voltage=0
#arm_freq=1000
#core_freq=400
#sdram_freq=450
#over_voltage_min=0
#arm_freq_min=300
#core_freq_min=250
#sdram_freq_min=400
arm_64bit=1
dtoverlay=allo-boss-dac-pcm512x-audio
```
---
### Author:  [@MichaIng](https://dietpi.com/forum/u/MichaIng)
#### Post date: [11 March 2024 17:45 UTC](https://dietpi.com/forum/t/pi-zero-2w-service-fail-after-update-snapcast-client/19532/9 "2024-03-11T17:45:28Z")
Okay that looks all good. Note that you must reboot after every sound card change, to be effective.
> [@Art-Ev](#):
>
> Found something : when setting sound card on onboard hdmi or 3.5mm, `aplay -l` also returns `no soundcards found...` so it’s not the DAC (also DAC is working on my pi3 running an old installation).
And you did a reboot after that change? Can you check whether `/boot/config.txt` then contains `dtparam=audio=off` and no `dtoverlay=` line?
Looks like I need to dig out a new SD card for my Pi Zero. They are currently all running the new kernel/firmware packages, which do not equal the ones of the images we provide.
With the new kernel, HDMI audio on RPi Zero (1) W works, with “auto” and with “hdmi” selection. It has no 3.5mm jack, hence cannot test that.
---
### Author:  [@system](https://dietpi.com/forum/u/system)
#### Post date: [6 September 2024 05:46 UTC](https://dietpi.com/forum/t/pi-zero-2w-service-fail-after-update-snapcast-client/19532/10 "2024-09-06T05:46:12Z")
This topic was automatically closed 178 days after the last reply. New replies are no longer allowed.