# Ethernet not working in the new version of Orange Pi 3B
**URL:** https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689
**Category:** Troubleshooting
**Created:** [9 July 2024 17:41 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689 "2024-07-09T17:41:27Z")
**Posts on this page:** 20
**Page:** 1
### Author:  [@raphamotta](https://dietpi.com/forum/u/raphamotta)
#### Post date: [9 July 2024 17:41 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/1 "2024-07-09T17:41:27Z")
Orange Pi 3B has a new version, 2.1:
[Orange Pi 3B V2.1 SBC has been revamped with better WiFi 5 connectivity, M.2 2280 NVMe/SATA SSD socket - CNX Software (cnx-software.com)](https://www.cnx-software.com/2024/06/07/orange-pi-3b-v2-1-sbc-better-wifi-5-m2-2280-nvme-sata-ssd-socket/)
I got this new board this week. I know the new thing is the wifi chip, and wifi is working fine. For some reason, the problem is the ethernet, there’s no connectivity.
Ethernet is working fine in the official Linux version of Opi 3B.
What can I do to help to solve this issue?
---
### Author:  [@Joulinar](https://dietpi.com/forum/u/Joulinar)
#### Post date: [10 July 2024 08:18 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/2 "2024-07-10T08:18:35Z")
not sure but maybe @MichaIng would be able to assist
---
### Author:  [@srm](https://dietpi.com/forum/u/srm)
#### Post date: [10 July 2024 15:54 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/3 "2024-07-10T15:54:53Z")
I am running into the same experience that @raphamotta noticed. In addition, I ran into a few more problems:
1. I couldn’t make the emmc bootable using the uboot packages with dietpi.
2. Updating the SPI flash to boto from an m.2 nvme did not work as well. My drive was detected, I was able to mount it and also transfer the boot image to it as well.
I am temporarily on the Orange pi debian. The main difference that I see is that they are using the 5.10 raxda kernel. This is my lspci and ethtool output from orange debian, which probably isn’t of much use.
```auto
root@orangepi3b:/home/orangepi# ethtool eth0
Settings for eth0:
Supported ports: [TP MII]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Unknown! (255)
Auto-negotiation: on
master-slave cfg: preferred slave
master-slave status: unknown
Port: Twisted Pair
PHYAD: 0
Transceiver: external
MDI-X: Unknown
Supports Wake-on: ug
Wake-on: d
Current message level: 0x0000003f (63)
drv probe link timer ifdown ifup
Link detected: no
root@orangepi3b:/home/orangepi# ethtool --driver eth0
driver: st_gmac
version: Jan_2016
firmware-version:
expansion-rom-version:
bus-info:
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: yes
supports-priv-flags: no
root@orangepi3b:/home/orangepi# lspci
00:00.0 PCI bridge: Fuzhou Rockchip Electronics Co., Ltd Device 3566 (rev 01)
01:00.0 Non-Volatile memory controller: Sandisk Corp WD Blue SN550 NVMe SSD (rev 01)
```
---
### Author:  [@lopirata](https://dietpi.com/forum/u/lopirata)
#### Post date: [11 July 2024 17:48 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/4 "2024-07-11T17:48:24Z")
Some things I learned about Opi3B:
1- There are at least two versions of the 3B PCB: v1.0 and v2.1. 1.1 has 3.3v PHY, 2.1 has 1.8v PHY.
This is well documented on orangepi site, but this changes are not on linux kernel, so, DietPi can’t handle it properly, and is not their fault.
2- Because of these PHY voltage diference, I don’t know if using DietPi is even safe,
3- Official OrangePi images work very weel on both board versions, but, to me, there’s a huge problem: Rockchip video acceleration only works on kernel 6.8 and above, and official images only ships with 5.10.X kernel.
4- Xunlong (orangepi boark maker) updated kernel sources, but as long as I know, linux kernel mantainers didn’t accepted the changes yet, so, there’s some time ahead before functional support from DietPI (and again, not their fault).
I’ll continue using official images and wait until linux kernel support.
---
### Author:  [@raphamotta](https://dietpi.com/forum/u/raphamotta)
#### Post date: [13 July 2024 15:52 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/5 "2024-07-13T15:52:09Z")
> [@lopirata](#):
>
> 1- There are at least two versions of the 3B PCB: v1.0 and v2.1. 1.1 has 3.3v PHY, 2.1 has 1.8v PHY.
> This is well documented on orangepi site, but this changes are not on linux kernel, so, DietPi can’t handle it properly, and is not their fault.
>
> 2- Because of these PHY voltage diference, I don’t know if using DietPi is even safe,
Maybe that’s why my board becames defective:
[Can’t boot Dietpi on Orangepi 3B from SD or eMMC (Armbian works) - Troubleshooting - DietPi Community Forum](https://dietpi.com/forum/t/cant-boot-dietpi-on-orangepi-3b-from-sd-or-emmc-armbian-works/20547)
---
### Author:  [@MichaIng](https://dietpi.com/forum/u/MichaIng)
#### Post date: [13 July 2024 17:30 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/6 "2024-07-13T17:30:43Z")
I just triggered an update for our Orange Pi 3B kernel and bootloader packages. Since the Armbian image seems to work, according to the other topic, ours should then as well. Or is the Ethernet issue present with latest Armbian as well?
---
### Author:  [@raphamotta](https://dietpi.com/forum/u/raphamotta)
#### Post date: [14 July 2024 13:35 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/7 "2024-07-14T13:35:58Z")
> [@MichaIng](#):
>
> Or is the Ethernet issue present with latest Armbian as well?
The issue is present in the latest version… no Ethernet connectivity
---
### Author:  [@lopirata](https://dietpi.com/forum/u/lopirata)
#### Post date: [16 July 2024 13:28 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/9 "2024-07-16T13:28:10Z")
Just saw that Linux Kernel 6.11 will support OPi3Bv2.1.
Time to wait now?
Anyway, there is any way to compile 6.11 kernel by myself and patch it into current images?
---
### Author:  [@Joulinar](https://dietpi.com/forum/u/Joulinar)
#### Post date: [17 July 2024 07:15 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/10 "2024-07-17T07:15:59Z")
as long as you don’t know what to do, you should not try to compile own kernel 😉
---
### Author:  [@lopirata](https://dietpi.com/forum/u/lopirata)
#### Post date: [17 July 2024 15:12 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/12 "2024-07-17T15:12:41Z")
> [@lopirata](#):
>
> I can compile kernel for my own laptop, but I’m curious about how to do it for DietPi and my board.
> Curiosity moves you forward, your thinking moves us backward.
Dude, I’m curious about how to do it for DietPi and my board, asking how to do it.
Curiosity moves you forward, your thinking moves us backward.
---
### Author:  [@juliawhites](https://dietpi.com/forum/u/juliawhites)
#### Post date: [22 July 2024 12:38 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/13 "2024-07-22T12:38:39Z")
> [@raphamotta](#):
>
> Orange Pi 3B has a new version, 2.1:
>
> [Orange Pi 3B V2.1 SBC has been revamped with better WiFi 5 connectivity, M.2 2280 NVMe/SATA SSD socket - CNX Software (cnx-software.com)](https://www.cnx-software.com/2024/06/07/orange-pi-3b-v2-1-sbc-better-wifi-5-m2-2280-nvme-sata-ssd-socket/)
>
> I got this new board this week. I know the new thing is the wifi chip, and wifi is working fine. For some reason, the problem is the ethernet, there’s no connectivity.
>
> Ethernet is working fine in the official Linux version of Opi 3B.
>
> What can I do to help to solve this issue?
Ensure that you have the correct drivers and kernel support for the new Orange Pi 3B V2.1 Ethernet hardware. Check for any firmware updates or configuration settings specific to the new board version.
---
### Author:  [@MichaIng](https://dietpi.com/forum/u/MichaIng)
#### Post date: [28 August 2024 22:25 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/14 "2024-08-28T22:25:39Z")
I generated a new image with new kernel: [https://dietpi.com/downloads/images/DietPi\_OrangePi3B-ARMv8-Bookworm.img.xz](https://dietpi.com/downloads/images/DietPi_OrangePi3B-ARMv8-Bookworm.img.xz)
Linux 6.10, hence no native mainline support yet, but maybe the driver got an update.
---
### Author:  [@boxer](https://dietpi.com/forum/u/boxer)
#### Post date: [31 August 2024 06:38 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/15 "2024-08-31T06:38:59Z")
> [@lopirata](#):
>
> Time to wait now?
You can skip middle man and use Armbian without “diet”. Armbian daily builds:
> **[Armbian Leaflet #25 - Armbian](https://www.armbian.com/newsflash/armbian-leaflet-25/)**
>
> Dear Armbians, Armbian point releases are times when our entire team works diligently to stabilize our highly complex ecosystem. We understand that, despite our best efforts, there will always be some issues that may not work perfectly. We estimate...
---
### Author:  [@raphamotta](https://dietpi.com/forum/u/raphamotta)
#### Post date: [1 September 2024 17:52 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/16 "2024-09-01T17:52:51Z")
Yet, no Ethernet so far… at least, it boots. Latest armbian gives a kernel panic error
---
### Author:  [@lopirata](https://dietpi.com/forum/u/lopirata)
#### Post date: [2 September 2024 22:31 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/17 "2024-09-02T22:31:58Z")
Waiting kernel 6.11 to be released officially. Even Armbian edge kernels are 6.10.y and OPi3B v2.1 dtb are on 6.11.
---
### Author:  [@raphamotta](https://dietpi.com/forum/u/raphamotta)
#### Post date: [23 September 2024 23:13 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/18 "2024-09-23T23:13:45Z")
@MichaIng latest armbian already support ethernet on Orange Pi 3B 2.1
[https://dl.armbian.com/orangepi3b/Bookworm\_vendor\_minimal](https://dl.armbian.com/orangepi3b/Bookworm_vendor_minimal)
---
### Author:  [@MichaIng](https://dietpi.com/forum/u/MichaIng)
#### Post date: [24 September 2024 17:06 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/19 "2024-09-24T17:06:32Z")
But that one is the vendor kernel Linux 6.1, while I would prefer to use mainline Linux right from the start.
We can switch to Linux master branch with our Armbian fork and do a test build, just to see whether it will work. I mean we could also provide a dedicated vendor kernel image, just to keep you guys started. Can be migrated to mainline kernel any time later.
---
### Author:  [@VittorioParagallo](https://dietpi.com/forum/u/VittorioParagallo)
#### Post date: [8 October 2024 23:13 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/20 "2024-10-08T23:13:22Z")
i solved the ethernet issue by switching the transmission speed in the config menu from auto to 100 mb.
For the reboot question after first boot from eMMC, i switch off the device, insert an sd card on which there is another linux distro, power on and from there i execute the sudo nand-install (i don’t remember well the command) to flash the bootloader in the spi. now everything works.
---
### Author:  [@ankagar](https://dietpi.com/forum/u/ankagar)
#### Post date: [11 October 2024 14:59 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/21 "2024-10-11T14:59:20Z")
Have run into the same issue
- ethernet not working
- not booting after reboot
will try out the suggestions from @VittorioParagallo
@MichaIng would it be possible to build a try out image with the vendor linux?
I really like the minimalism of dietpi and want to avoid other distros if possible
---
### Author:  [@MichaIng](https://dietpi.com/forum/u/MichaIng)
#### Post date: [11 October 2024 18:28 UTC](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689/22 "2024-10-11T18:28:03Z")
Okay shit, we pushed the Linux 6.11 based kernel to the APT repo already, but it contains 2 device trees for the two revisions
This of course does not work with our `/boot/dietpiEnv.txt`, which defines `rk3566-orangepi-3b.dtb`. I hence took the package off the repository again.
@ankagar
I guess you upgraded the kernel already, so that reboot fails expectedly, as of above change, right? In that case, please mount the rootfs on another Linux system, edit `/boot/dietpiEnv.txt`, and append adjust the `fdtfile` line accordingly:
```auto
fdtfile=rockchip/rk3566-orangepi-3b-v2.1.dtb
```
That should fix boot and, as I cannot imagine any other reason for providing two device trees, Ethernet as well.
If that works: Mainline U-Boot supports those two device trees OOTB: [board: rockchip: Add Xunlong Orange Pi 3B · u-boot/u-boot@a52099b · GitHub](https://github.com/u-boot/u-boot/commit/a52099b#diff-1ca8d9ce95828f53150c73714c349fd38c171c4c3d51c2e606fea59a4358af84)
And I pushed the mainline U-Boot based package to your APT server already. So it it works, can you try to remove the `fdtfile` entirely from `/boot/dietpiEnv.txt`? The new bootloader should then pick the correct device tree automatically. But you also need to flash that one:
```sh
sudo /boot/dietpi/func/dietpi-set_hardware flash-u-boot-mmc
sudo sed -i '/^fdtfile=/d' /boot/dietpiEnv.txt
sudo reboot
```
It is pretty non-trivial to do this migration properly, since the new kernel does not work with the old config and the new config does not work with the old bootloader, so all need to be updated and adjusted automatically. However, since the old kernel provided a device tree for v1.1 revision only, I’ll adjust our Armbian fork to ship this particular package with a symlink from old dtb name to new v1.1 dtb. That way systems keep running like before when upgrading this kernel. The next DietPi update will then flash the new bootloader image and remove the `fdtfile` entry, so that v2.1 revisions will have Ethernet.
[Next page](https://dietpi.com/forum/t/ethernet-not-working-in-the-new-version-of-orange-pi-3b/20689.md?page=2)